Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Tampa?
New gate installation in Tampa typically runs $2,200 to $9,500 for most residential jobs, and $6,000 to $22,000+ once you move into commercial or heavy-duty automated systems. A basic manual driveway gate with a simple swing or slide setup usually lands near the low end. Add an operator, keypad, safety loops, and access control on a wide double gate, and you’re in the middle to upper range. The number that actually applies to your property depends on the gate style, opening width, and whether we’re wiring a full electric system or hanging manual hardware. We give free, itemized estimates so you’re not guessing.
Tampa Gate Company is a gate-only company. That matters when you’re pricing a new install, because a generalist quotes broadly and pads for things they don’t do often. We spec, build, and wire gate systems every day, across nine of the major brands you’ll find on homes and businesses around Hillsborough County. Here’s what our Gate Installation services actually cost in Tampa in 2026, and what moves the price up or down.
Gate Installation Cost Breakdown (2026)
These are real Tampa-market ranges for the pieces that make up a typical job. Prices vary with material costs, site conditions, and how much electrical and access-control work is involved.
| Line Item | Typical Tampa Price Range (2026) |
|---|---|
| Basic manual driveway gate (single swing, ornamental steel) | $1,800 – $4,200 |
| Manual double swing or slide gate (ornamental steel or aluminum) | $3,500 – $7,500 |
| Gate operator / motor (residential swing or slide) | $1,500 – $3,200 installed |
| Control board, keypad, remote, and basic access wiring | $600 – $1,800 |
| Safety loops and photo-eye sensors | $400 – $1,100 |
| Intercom or video entry system | $800 – $3,500 |
| Concrete footings and site prep (grade work) | $600 – $2,500 |
| Complete automated residential driveway system | $5,500 – $13,000 |
| Commercial / high-traffic automated gate (DoorKing, FAAC, etc.) | $8,000 – $22,000+ |
What pushes a Tampa install toward the top of these ranges: wide openings that need heavier motors, gates on a slope where drainage and footing work get complicated, and properties that need long trenching runs to bring power and access-control cable out to the gate. What keeps it lower: a standard single-gate opening, existing conduit already in place, and sticking to a proven operator brand we work on directly. Our Gate Installation in Tampa page covers the full service, and we’ll walk you through which tier fits your property.
What Affects Gate Installation Pricing in Tampa
- Gate style and material. Ornamental steel and aluminum are the most common choices for Tampa homes, and they vary in cost per linear foot. A tall, heavy steel gate needs a bigger operator and stronger footings, which raises the number. Chain link and lighter aluminum come in lower.
- Single vs. double and opening width. Wide double openings need more material, a heavier-duty motor, and more concrete. A 16-foot clearance costs meaningfully more than a 12-foot one, and the motor tier climbs with it.
- Electric vs. manual. A manual gate is hardware and labor. An automated gate adds an operator, a control board, remotes or a keypad, and safety devices. Most Tampa homeowners go electric, so this is the single biggest cost swing on the job.
- Access control and entry hardware. Keypads, intercoms, video entry, and phone-app controls all add to the total. We wire these every week, so we match the access control to the operator brand instead of bolting on whatever’s cheap.
- Power and trenching. If power doesn’t already reach the gate location, you’re paying for trenching and conduit from the nearest source. The longer the run, the higher the labor line. This is one of the most site-specific costs, and it’s why an on-site look beats a phone guess.
- Coastal and storm exposure. Tampa’s humidity, salt air near the bay, and hurricane season all push toward corrosion-resistant materials, galvanized or treated hardware, and operators rated for wind cycling. Skimping here is what leads to callbacks a couple of years in, and we’d rather spec it right the first time.
We’re also realistic about the other lever on price: repair versus replace. If you’re staring at a gate that mostly works, the honest answer is often a repair, not a new install. We repair first and only recommend replacement when repair isn’t the right call. That’s not a sales line, it’s how a gate-only company earns repeat business in Tampa. You can see how we handle the repair side through our gate repair and home pages.
How to Save on Gate Installation
Here’s where the money actually comes out of a Tampa gate project, without cutting corners that bite you later.
- Get the operator brand matched to the gate. A motor that’s oversized or undersized for the gate costs you more up front or fails early. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems, so we pick the operator that fits your gate and your access-control plan. Wrong-fit motors are a common reason people overpay.
- Repair before you replace. If your current gate and operator are salvageable, repairing is far cheaper than a new install. Ask for a repair diagnosis first. Many “replacement” quotes turn out to be a control board, a sensor loop, or a worn operator that we can fix.
- Handle access control in one visit. Bundling the keypad, remotes, and safety loops into the installation trip saves the cost of a second mobilization. We plan the whole system at once.
- Keep power runs short if you can. Choosing a gate location near an existing power source cuts trenching. If you’re flexible on where the gate goes, that’s real money.
- Ask us for a free, itemized estimate. Ranges on a page are a starting point. A free estimate tells you exactly what your property needs, line by line, so you can compare gate to gate. Call (866) 976-0095 and we’ll walk your property or talk through photos.
FAQs – Gate Installation Cost
How much does a full automated gate installation cost in Tampa?
A complete automated residential driveway system in Tampa typically runs $5,500 to $13,000, and commercial or high-traffic systems can reach $8,000 to $22,000+. The range covers the gate, operator, control board, access control, and safety devices. Call (866) 976-0095 for a free itemized estimate, since your opening width and power situation move the number.
Is it cheaper to repair my gate or install a new one in Tampa?
Repair is almost always cheaper when the gate structure and operator are sound. A repair for a failed control board, sensor, or operator often costs a fraction of a new install. We recommend replacement only when the gate and hardware are beyond economical repair. Call (866) 976-0095 and we’ll diagnose first, then give you the honest call.
Do I need a permit to install a gate in Tampa?
Many Tampa gate installations, especially those with structural footings, electrical work, or near property lines, can require a permit depending on the scope and location. We’ll tell you what your specific project needs so you’re not caught off guard. Call (866) 976-0095 and we’ll cover the permit question for your property.
How much does an electric gate operator cost in Tampa?
A residential gate operator installed in Tampa generally runs $1,500 to $3,200, and that’s before access control and safety loops. Commercial operators cost more. We work on LiftMaster, FAAC, BFT, Viking, DoorKing, and Mighty Mule systems regularly, so we match the operator to your gate. Call (866) 976-0095 for an exact quote.
Can you install the gate and wire the access control in one job?
Yes. Installing the gate, operator, keypad, intercom, and safety loops together is typically more cost-effective than splitting the work across multiple visits. We plan the full system, wire it, and test it as one job. Call (866) 976-0095 to schedule a free estimate.
Why a Gate Specialist Costs You Less Over Time
A gate is a single, specialized piece of equipment, and the pricing reflects that. Generalists divide their attention across trades, which means they may miss the operator-brand fit, under-spec the footings, or quote access control that doesn’t match your system. We do gates and only gates. Every tool, every part, and every technician is focused on getting your gate to secure, working order. That focus is why our estimates hold up and why the system keeps working after we leave. If you want to understand the bigger picture of what we do beyond installs, our gate repair and electric gate repair pages show the same specialist approach across the service.
We also know the brands inside out. When your system is a LiftMaster swing operator, a FAAC slide gate, a DoorKing commercial unit, or a Ghost Controls driveway gate, we speak its language. That’s the difference between a company that reads the manual on your driveway and one that’s already familiar with it.
Ready for a real number? Call Tampa Gate Company at (866) 976-0095 for a free, itemized estimate on your new gate. We’ll look at your opening, your power situation, and your access-control plans, then tell you exactly what it costs and whether repair makes more sense than replacement. One call to a specialist, not a generalist with a side interest in gates.
Pricing reflects the Tampa market as of 2026. Tampa Gate Company offers free estimates – call (866) 976-0095.
What Our Customers Say
"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, had one with him, and we were moving cars again in under an hour."
— Rohan Singh"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
— Robert Norris"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
— Adam Lawson