Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Kenneth City, FL
Gate installation in Kenneth City means working with properties that were mostly laid out in the 1950s and 60s, before automation was ever part of the plan. Most driveways here have original chain-link or early aluminum gates, and many of them now carry opener arms bolted to posts that were never set in concrete for that kind of torque. That changes how we approach every job, because the right installation here usually starts with the post and the footing, not the gate panel itself.
Tampa Gate Company has served Kenneth City since 2013, and we work on gate systems the way a gate company should: as the only thing we do. If you’re weighing a new gate for a 1962 block home or replacing a rusted-through steel frame along a side yard, call (866) 976-0095 and we’ll give you a straight answer and a written price.
Why Kenneth City Homes Are Different
Kenneth City is a compact Pinellas County enclave where homes sit close together, many on lots where the fence line and the neighbor’s yard are separated by inches, not feet. The housing stock is dominated by small single-story block-and-stucco ranch homes and low-rise condos built between the 1950s and early 1970s, and the fences and gates from that era are still standing on a lot of properties.
The climate does the rest. Subtropical humidity, salt-laden air rolling in from Boca Ciega Bay a few miles west, and months of rainy-season storms all work against steel. Hinges rust through at the welds. Bottom rails rot out on chain-link frames. Wood gates swell and bind in the damp. And because lots are so tight, a gate that drops half an inch off its hinges scrapes a neighbor’s fence or a shared privacy hedge, which turns a small repair into a dispute if it goes unaddressed.
The defining Kenneth City pattern is rusted hinge brackets and sagging posts on the narrow side-yard gate lines. Many of the original chain-link driveway gates still carry their 1960s posts, and opener motors have been bolted on as an afterthought. When we work here, we plan for re-hanging, shimming, and re-welding before we ever talk about replacing a whole gate.
Styles & brands we work with
Our Main Kenneth City Services
Most calls we take in Kenneth City fall into two buckets: the gate won’t open or close reliably, or the gate is worn out and needs to come down and be replaced. Here’s how each one works in this area.
Gate Repair in Kenneth City
Kenneth City repair work tends to be mechanical first: rusted hinge brackets, sagging posts, rollers that jump the track, and latch hardware that’s seized from salt air and humidity. On motorized gates, the problems stack up differently, with control boards, safety loops, and limit switches failing as often as the motor itself. Because most lots here are fenced line to line, a misaligned gate becomes a neighbor’s problem fast, so we prioritize getting the gate rehung square and moving cleanly. Read the full detail on Gate Repair in Kenneth City.
Electric Gate Repair in Kenneth City
An electric gate in Kenneth City has to deal with moisture, corrosion, and frequent power interruptions from summer storms. We diagnose the motor, board, safety sensors, and the loop detector all together, because in this climate the failure is rarely just one component. We work on systems from LiftMaster, FAAC, BFT, Mighty Mule, and several other brands, so the diagnosis isn’t a guess. For the full scope, see Electric Gate Repair in Kenneth City.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Gate Installation in Kenneth City
Gate installation in Kenneth City is a different job than in newer subdivisions. Most of the homes here were built in the 1950s and 60s, so when a gate comes down, what we’re usually dealing with is an old post that was never set deep enough, chain-link or steel framing that has rusted through at the welds, and a driveway width that was designed for one car, not an automated slide gate. The subtropical humidity and salt air mean new steel has to be prepped and finished for this specific environment, not just bolted into place.
That’s why a proper installation starts with the footing and the post, because no gate panel, opener, or hinge kit fixes a post that moves. We handle the whole scope as a gate specialist, from removing the old gate and setting new posts to installing the panel, the opener, and the safety edges, all quoted before we start. Visit our Gate Installation page for the full service overview.
Automatic Gate Installation
Signs you need it
You’re opening and closing the gate by hand every time, or an existing opener keeps tripping its limit and binding on the post.
What it costs in Kenneth City
Automatic gate installation in Kenneth City typically runs $1,500 to $7,500, depending on the opener, gate size, and whether new posts and conduit are part of the job.
How we do it
We set or verify the posts, mount the opener and gate hardware, run the power and control wiring, and program the travel limits and safety loops before testing the full cycle.
Driveway Gate Installation
Signs you need it
The existing driveway gate is rusted through at the bottom rail, sagging badly, or too narrow for the vehicles you actually drive now.
What it costs in Kenneth City
Driveway gate installation in Kenneth City typically runs $2,000 to $8,000, with the spread driven by gate length, material, and whether automation is added at the same time.
How we do it
We measure the driveway opening, check the soil and existing posts, remove the old gate, set new posts to the correct depth, and hang the new gate so it clears the ground and swings freely.
Sliding Gate Installation
Signs you need it
Your driveway slants or has limited swing clearance, and a swinging gate would hit a wall, a hedge, or the neighbor’s fence line.
What it costs in Kenneth City
Sliding gate installation in Kenneth City typically runs $2,500 to $9,000, with the higher end reflecting track, motor, and concrete pad work.
How we do it
We pour or verify the concrete track base, set the guide rollers and posts, hang the gate on the track, then mount and program the motor with the safety edges and limit stops.
What Gate Installation Costs in Kenneth City
| Item | Typical range in Kenneth City |
|---|---|
| Automatic gate installation | $1,500 – $7,500 |
| Driveway gate installation | $2,000 – $8,000 |
| Sliding gate installation | $2,500 – $9,000 |
Does a new gate in Kenneth City need a permit?
Yes, in most cases. Kenneth City requires permits for new gate posts, footings, and any electrical work on an automated opener, and we handle the permit scope as part of the job rather than leaving it to you.
Can you replace just the gate panel and keep my existing posts?
Sometimes, but in Kenneth City the posts from mid-century homes are often rusted below grade or not set in concrete, so we inspect them first. If the posts are solid and plumb, we’ll re-use them and save you the excavation.
Brands We Service in Kenneth City
We service and install most gate brands you’ll find in Kenneth City, including LiftMaster, Mighty Mule, FAAC, and BFT systems. The advantage of a gate-only company is that we carry the common boards, sensors, and hardware for these brands in stock, which shortens the wait when a part fails. See our brands for the full list.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Kenneth City, FL
| Service | Typical range in Kenneth City |
|---|---|
| Automatic gate installation | $1,500 – $7,500 |
| Driveway gate installation | $2,000 – $8,000 |
| Sliding gate installation | $2,500 – $9,000 |
Prices move up in Kenneth City when we have to replace rusted posts, repair a footing, or add a dedicated circuit for a new opener, and when the old gate has to be cut out rather than simply unbolted. Every job is quoted as a fixed price, agreed before we start, so the number we give you is the number on the invoice.
Neighborhoods We Serve in Kenneth City
We cover the entire city and the surrounding Pinellas County area, including:
- The neighborhoods around 58th Street North and 54th Avenue, where the original mid-century homes still carry their first gates.
- The side streets off 62nd Street North, with narrow side-yard fence lines and tight driveway clearances.
- The blocks near Kenneth City Park and the surrounding residential grid.
- The condo and smaller residential clusters near the western edge of the city.
Most Kenneth City calls are within a short drive of our Tampa base, and we schedule service windows that match the job, not a generic four-hour block.
Service Area – Cities Near Kenneth City
Kenneth City sits in the middle of a tightly packed Pinellas County corridor, and we run the same gate-only service into the communities around it. That includes Bay Pines, FL, Lealman, FL, West and East Lealman, FL, and Pinellas Park, FL. If you’re a few minutes outside Kenneth City, call and we’ll tell you straight whether we cover your address.
Serving Kenneth City, FL — Our Local Coverage Area
We’re based in the Kenneth City area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Kenneth City
For urgent issues like a gate that won’t close or an opener that has failed, we can usually reach Kenneth City the same day or the next morning. We’ll give you a realistic window when you call, not a vague promise.
Yes. We run the power, control wiring, safety loops, and keypad or intercom connections as part of the installation. The only thing we don’t do is tie into the electrical panel itself, which we coordinate through a licensed electrician if your property needs it.
Yes. Most of the gates in Kenneth City were installed years ago by companies that no longer exist, and we regularly take over maintenance and repair on those systems. We’ll assess what you have and tell you what’s actually worth fixing.
If your gate is sagging, rusted, or not opening when you need it to, call Tampa Gate Company at (866) 976-0095. We’ll give you a free estimate and a fixed price before any work begins, and we’ll leave the gate closing square, latching securely, and working the way it should.
What happens when you call
- 1A real person answersNo phone trees — talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you — the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Kenneth City Customers Say
"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
— Scott Miller"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
— Rachel Meyer"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
— Diego Guzman