Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Repair in Highland City, FL | Tampa Gate Company
We repair Ghost Controls gate operators across Highland City, and the short version is this: most calls after a summer storm are a fried control board, not a dead motor. We’re an independent service company, not a Ghost Controls dealer, and we work on AXO, AC, and solar-charged lines every week. The local factor that changes everything here is lightning. If your gate stopped working after a storm, call (866) 976-0095 for a free estimate.
Why Highland City Residents Choose Us for Ghost Controls Service
We’re a gate-only shop. That means every tech in our crew spends their day on swing gates, slide gates, and operators, not splitting time between garage doors and HVAC callouts. Noel Carver started Tampa Gate Company after years of working on gate systems around the Tampa Bay area, and the focus has always been narrow: diagnose the system, fix what’s actually broken, and skip the pressure to replace something that still has life in it.
For Highland City homeowners, that matters because Ghost Controls systems have specific failure patterns that a generalist will misread. A board that won’t power after a strike. A solar battery that’s sulfated from heat and humidity. A hinge that’s rusting out and tripping the operator’s obstruction sensing. We know these problems by sight. If you need Ghost Controls sales & service support, we’re built for it.
Styles & brands we work with
Common Ghost Controls Gate Repair Problems We Solve in Highland City
- Lightning-fried control boards. The motor bench-tests fine, but nothing powers up. Highland City sits in one of Florida’s most active lightning corridors, and June through September afternoon storms send surges through low-voltage gate wiring. We test the board, the transformer, and the keypad receiver before recommending anything.
- Surge-burned keypads and remote receivers. Gates that were never properly grounded at the post take surge damage through the accessory wiring. A board swap alone won’t hold. We add post grounding and check surge protection, then replace the burned components.
- Rusted hinge plates and frame steel on chain-link and double-swing gates. Irrigated lawns and sandy soil keep moisture against the post. Rusted hinges load the operator arm and trip obstruction sensing, so the gate reverses or stalls partway. We replace or reinforce the hardware, then re-set limit travel.
- Battery and charge-controller failure on solar Ghost Controls units. Humid, storm-heavy summers shorten battery life. Often the battery is sulfated or the charge controller is corroded, not the motor. We test the full charging circuit and replace what’s actually failed.
- Limit-switch and magnet alignment drift. Gates on larger lots settle as sandy soil shifts. The arm opens too far or closes short, or the operator thinks the gate is off its travel. We reset limits and remount magnets, then run a full open-close cycle to verify.
Ghost Controls Service in Highland City: What Local Conditions Mean for Your Equipment
Highland City’s larger fenced suburban lots and US 98 corridor properties mean Ghost Controls in Bartow and nearby areas often land on chain-link and double-swing driveway gates as on ornamental ones. That hardware rusts at the hinge and frame in our humid, irrigated setting, so a “dead operator” call is frequently a storm-fried board sitting on top of a gate that’s already binding from rust. The operator gets blamed, but the gate itself was fighting it weeks before the strike.
The thing to know about the US 98 corridor: after a big summer storm, you can bet a handful of calls come in from the same subdivision with gates that “just stopped working.” The opener motor is fine, the lightning took out the control board. So the first question a local gate tech asks is whether the neighbor’s gate is also glitching. That single question changes the diagnosis from a mechanical failure to an electrical event, which points the repair in a completely different direction.
Ghost Controls Models & Products We Service in Highland City
We service the full Ghost Controls residential range. That includes the AXO heavy-duty single swing (AXO201 and AXO251), the AC-powered single swing (AC200 and AC251), the solar-charged TDS battery operator and solar kits, and the dual-swing AXO and AC dual configurations. We stock genuine Ghost Controls control boards, limit magnets, actuator arms, and battery/charge-controller kits where OEM is the right call. We also use quality aftermarket actuators, keypads, and hardware where they hold up better in Florida humidity and sandy soil. A board salvageable after a strike gets repaired. Full replacement only comes up when the operator housing or arm geometry is genuinely shot.
See the difference
Before
After
Before
After
Before
AfterGhost Controls Service Pricing in Highland City
What you’ll pay depends on what’s failed. A control board replacement on a single-swing Ghost Controls unit typically runs $325 to $525 installed, including the board, wiring check, and post-grounding inspection. A new keypad or remote receiver is usually $150 to $300. Battery and charge-controller replacement on solar units runs $200 to $400. Full operator replacement, when the housing or arm is damaged beyond repair, typically lands between $900 and $1,800 depending on the model and gate weight. We quote the price before any work starts, so you know exactly what you’re approving. Call (866) 976-0095 and we’ll walk through what your specific system needs.
Serving Highland City, FL — Our Local Coverage Area
We’re based in the Highland City area and know this community well, and we also handle Ghost Controls repair in Crystal Lake. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs – Ghost Controls Gate Repair in Highland City
The control board took a surge. The motor is a dumb component, it just turns when the board tells it to. In Highland City, summer lightning strikes fry the low-voltage logic board while the arm sits there looking perfectly fine. We bench-test the motor to confirm it’s good, then replace the board and check grounding so it doesn’t happen again next storm. Call (866) 976-0095 with your model number and we’ll give you a real cost estimate.
We service both. Solar-charged TDS units and AC-powered operators, including those we service for Ghost Controls in Lakeland Highlands, have different failure profiles. Solar systems tend to fail at the battery or charge controller, especially after a hot, humid summer. AC units fail at the board or a transformer. We test the full charging circuit on solar units, not just the battery, because a bad controller will kill a new battery in weeks.
Usually the gate. Rusted hinges, a sagging leaf, or sandy soil shifting the post means the operator has to work harder, and the obstruction sensing kicks in. We check the gate’s physical movement first, then test the board. If the gate binds, we fix the hardware and reset limits before blaming the operator. It’s cheaper to correct a rusted hinge than to replace an arm that’s been fighting it for months.
Yes, and we do it regularly. If the strike only took out the low-voltage board, the operator housing and arm are usually fine. We replace the board, test the transformer and accessory wiring, and restore the gate to working order the same visit. Full operator replacement only makes sense when the housing is cracked, the arm geometry is damaged, or the motor itself is burned out. We’ll tell you which situation you’re in before any work begins.
It confirms it. When multiple gates in the same subdivision fail after one storm, the cause is almost always a neighborhood-wide surge event, not a mechanical failure. Both operators likely have fried control boards and possibly burned keypad receivers. We’ll test both boards, swap what’s dead, and recommend grounding upgrades so the replacement boards aren’t the next ones to go. Call (866) 976-0095 for a free estimate on your address.
Service Areas Near Highland City
Our Ghost Controls service covers Highland City and the surrounding communities. We work regularly in Tampa, Progress Village, Palm River-Clair Mel, East Lake-Orient Park, Egypt Lake-Leto, and Carrollwood. If you’re on the Lakeland side, you’ll find our Highland City service area portal useful for booking. For coastal customers, we also run Ghost Controls service in Cortez and Ghost Controls service in Bradenton Beach.
Book Your Ghost Controls Service in Highland City Today
If your Ghost Controls gate is down, call (866) 976-0095 for a free estimate. We’ll walk through what your system is doing, give you a straight answer on whether it’s a board, a battery, or a rusted gate that’s fighting its own operator, and get it back to secure working order. A gate that almost works is a gate that doesn’t work.
Written by Noel Carver, Owner at Tampa Gate Company, serving Highland City, FL since 2005.