Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Fort Myers Shores
When a gate stops working in Fort Myers Shores, it’s rarely a small inconvenience. It’s a security gap on a property that sits just feet above the water table, where every day of delay means a corroded hinge worsens or a misaligned sensor leaves your family exposed. We’re Tampa Gate Company, and we specialize in Gate Repair that accounts for this specific stretch of the Caloosahatchee. Salt air, storm surge, and decades-old hardware all factor into how we diagnose and fix your system. If your gate is binding, sagging, or dead, call us at (866) 976-0095, and we’ll have a technician on it.
Why Tampa Gate Company Is Fort Myers Shores’s Preferred Gate Repair Company
Most repair companies treat gates as a side job. We don’t. Every technician we send into Fort Myers Shores works only on gates, from the simplest chain-link swing to a full automated LiftMaster system. That focus is why we can identify a failing bottom rail on a 1970s wrought-iron gate before the homeowner even notices the scrape, and why a diagnosis that takes a generalist three visits takes us one.
Local reputation matters here. Fort Myers Shores homeowners talk to each other, especially after a named storm knocks out half the neighborhood’s gates. We’ve built standing in this community by showing up to Old Olga Road, to homes near the canals off Tice Street, and to the quiet streets off Buckingham Road with the same promise: repair first, replace only when repair isn’t the right answer. Our owner, Noel Carver, holds the whole team to that standard, because a gate specialist who pushes replacements on a repairable system is not a specialist at all.
Styles & brands we work with
Gate Welding in Fort Myers Shores
Gate welding in Fort Myers Shores is one of our most common callouts, and it’s not the kind of welding done in a clean fabrication shop. It’s repair welding on gates that have lived through decades of humid salt air, several hurricane seasons, and soil that heaves when saturated. We see steel gates with bottom rails rusted through from the inside, hinge plates that have fatigued from wind load, and chain-link posts that have snapped at the base after a storm surge softened the ground around them. Depending on the extent of the damage, a typical gate welding repair in Fort Myers Shores runs $250 to $700 for a residential gate, with larger commercial setups going higher based on the amount of steel and the number of hinge plates that need replacement.
Bottom Rail and Hinge Plate Repair
The bottom rail is where Fort Myers Shores gates die first. Salt-laden air off the Caloosahatchee settles right at the lowest point of the gate, and peeling paint hides rust that can chew through a rail in a few years. We cut out the rot, weld in new steel, and treat the area so the same failure doesn’t repeat in two seasons.
Post and Footing Refits
Heavy rains and occasional flooding leave the ground in Fort Myers Shores spongy. A gate post that settled an inch can throw the entire gate out of alignment, and welding a new hinge plate onto a leaning post fixes nothing. We dig out the old footing, pour a deeper one suited to this soil, and re-set the post before welding anything to it.
Commercial Gate Repair in Fort Myers Shores
Commercial gate repair in Fort Myers Shores comes with a different set of stakes. A failed gate on a rental property, a boat storage yard, or a small business off Buckingham Road means tenants can’t get in, visitors can’t leave, and security is compromised. We work on commercial systems across the area, from simple chain-link swing gates to automated slide gates with vehicle detection loops and keypad access. A commercial gate repair in Fort Myers Shores typically runs $400 to $1,800 depending on whether we’re replacing a damaged operator, rebuilding a section of track, or rewiring a control board that took a surge during a storm.
Automated Systems and Access Control
Commercial gates in Fort Myers Shores rarely fail mechanically first. They fail electrically. A control board that sat in a humid enclosure for five years develops corrosion on the terminals, and a safety loop that cracked under heavy truck traffic stops detecting vehicles. We diagnose motor, board, and loop issues in one visit, because on a commercial gate, every hour of downtime costs you money.
Storm Restoration for Multifamily and Commercial Properties
After a hurricane, property managers call us about gates that won’t open, gates that won’t stay open, and gates that bent when wind caught a solid infill panel. We stage these jobs carefully: first we get the gate into a safe position, then we assess whether the operator survived the power surge, then we rebuild or replace what the storm took.
Trusted Brands We Service in Fort Myers Shores
We work on Mighty Mule, LiftMaster, FAAC, BFT, and most other residential and commercial gate systems you’ll find in Fort Myers Shores. That matters here because so many homes off Old Olga Road were upgraded to openers in the 1990s and early 2000s, meaning the boards are now failing from age and humidity at the same time the mechanical hardware is giving out. We understand those older systems, and we stock replacement boards, remote transmitters, and hinge hardware so we’re not making you wait on a part that has to ship from Texas.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Repair Problems We See in Fort Myers Shores Homes
- Rust-through on bottom rails. The near-constant salt air off the Caloosahatchee settles on the lowest point of your gate, and we regularly find rails that look intact from above but are paper-thin underneath where peeling paint hid the corrosion.
- Sagging gates from saturated ground. Fort Myers Shores soil holds water. After heavy rains or a storm surge, post footings lose strength and gates drop at the latch side, binding against the post and stripping the operator gears.
- Wind fatigue on older hardware. Many homes here were built between the 1950s and 1980s, and the original gate hardware has absorbed decades of tropical wind loading. Hinges stretch, pickup points crack, and frames warp enough that the gate no longer closes squarely.
- Operator failures after power surges. Automated gates on homes and small commercial properties in Fort Myers Shores frequently lose their control boards when lightning or a grid surge hits the circuit. The motor may be fine, but the board needs diagnosis and often replacement.
Pricing for Gate Repair in Fort Myers Shores, FL
We quote every job before any work starts, and the price you agree to is the price you pay. No additions after the fact. For Fort Myers Shores, a hinge replacement or realignment typically runs $180 to $400. Gate welding repairs run $250 to $700 for residential work. Operator and control board repairs on automated systems fall between $350 and $1,200 depending on the brand and the extent of the electrical damage. Full gate replacement or new installation, when repair genuinely isn’t the right call, starts around $1,500 and goes up based on the size, material, and automation involved. Call (866) 976-0095 for an exact quote on your gate, and we’ll give you a written number before we touch anything.
We Also Serve Cities Near Fort Myers Shores
Our team covers the whole corridor along the Caloosahatchee, so when you need Gate Repair in Fort Myers Shores, we’re already nearby. We also work regularly in Buckingham, Olga, Gateway, and Tice, handling the same storm- and corrosion-driven repairs we see along Old Olga Road. Same specialist, same honest diagnosis, same repair-first approach.
Serving Fort Myers Shores, FL — Our Local Coverage Area
We’re based in the Fort Myers Shores area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Fort Myers Shores
Your automatic gate operator has a manual release mechanism, usually a keyed lock on the operator housing or a pull lever near the motor, that disconnects the drive chain or arm so the gate can slide or swing by hand. Don’t force the gate open against the operator, it can strip the gears and turn a power outage into a $500 repair. If you can’t locate the release or the gate won’t move freely even in manual mode, call us at (866) 976-0095 and we’ll walk you through it or send a tech out.
The Caloosahatchee River puts salt in the air all year, and Fort Myers Shores’s low elevation means that salty, humid air hangs over your property far more than it does even a few miles inland. Painted steel and wrought iron absorb that moisture at the bottom rail and around hinge pins, and rust starts where paint has a single chip. If your gate is older than about 15 years and hasn’t been inspected since before the last hurricane season, it likely has corrosion you haven’t seen yet.
Saturated ground, almost every time. When storm water soaks into the sandy soil around your gate post, the footing loses lateral support and the post begins to lean or settle under the gate’s weight. The gate drops at the latch and binds against the hinge post. Welding won’t fix it until the footing is re-set. We see this on homes along the river side of Old Olga Road more than anywhere else in the area.
First, check the bottom rail on both sides for fresh rust or cracking, especially under any peeling paint. Second, run your hand along the hinge pins and look for a gap that wasn’t there before. Third, cycle the gate and watch whether it closes squarely or lands short. If anything sounds strained or the gate drags at any point, stop using the operator and call us. Small problems after a storm become expensive failures within a few weeks in this climate.
Yes, and this is not optional. Any automated gate in Fort Myers Shores, residential or commercial, must meet UL 325 entrapment protection standards, which means working safety photocells and a properly calibrated force limitation setting on the operator. Flooding and salt exposure damage sensors over time, and a gate that doesn’t reverse when something is in its path is a serious liability. We test and replace safety edges and photocells on every automated gate we service.
Call Tampa Gate Company at (866) 976-0095 for fast, honest gate repair in Fort Myers Shores. Free estimates, upfront pricing, and a technician who knows your neighborhood and your gate.
Written by Noel Carver, Owner at Tampa Gate Company, serving Fort Myers Shores and the Caloosahatchee corridor.