Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Lake Placid
Gate repair in Lake Placid typically runs $185 – $480 for common hinge, post, and opener board work, and most jobs can be diagnosed and fixed in a single visit. We work on rural driveway gates all over Highlands County, from the 33852 neighborhoods around Lake June and Lake Placid proper out to the 33862 Lorida corridor. If your gate is sagging, seized, or the opener just hums and won’t move, call (866) 976-0095 and we’ll get a specialist to your property.
We know Lake Placid’s gate work doesn’t look like suburban gate work. Here, you’re dealing with long-run driveway entries on sandy lots, pasture gates on ranch parcels, and seasonal homes where a gate sits untouched from April to October. That changes how gates fail and what it takes to fix them properly. We plan our schedules around that reality.
Why Tampa Gate Company Is Lake Placid’s Preferred Gate Repair Company
We’re a gate-only company, which means every tech we send to Lake Placid spends their entire week working on gates. Not garage doors, not HVAC, not general handyman work. When a swing gate on a ranch property off CR 621 starts binding or an older FAAC board stops responding after a storm, we recognize the system on sight. That focus cuts diagnosis time and gets the repair done without guesswork.
Noel Carver built Tampa Gate Company around one idea: repair first, replace only when repair is the wrong call. For Lake Placid’s aging gates, that matters. A lot of companies want to sell you a new operator the moment they see an older control board. We carry replacement boards, hinge rebuild kits, and photocells for older systems, so we can often keep a legacy gate running for years at a fraction of replacement cost.
We service nine major gate brands including LiftMaster, FAAC, BFT, Viking, and Mighty Mule. That brand depth means we don’t show up to your Lake Placid property and scratch our heads at a niche operator. We’ve worked on the system before. We know its failure points.
Our Lake Placid customers call us directly because of word of mouth. Neighbors tell neighbors. When a snowbird returns in October to a dead gate on their Lake Placid property, they want one call to a specialist, not a generalist with a side interest in gates.
Styles & brands we work with
Sliding Gate Repair in Lake Placid
Sliding Gate Repair in Lake Placid usually runs $220 – $480 depending on whether the problem is the track, the rollers, the motor, or the board. On the sandy lots around Lake Placid and Lorida, slide gates pick up grit in the track and rollers, and posts shift as the sand settles. A gate that won’t slide smoothly is often an alignment and track-wear problem, not a motor failure.
Our team starts with a track and roller inspection, because that’s where Lake Placid’s soil conditions hit hardest. We check wheel wear, clean debris from the chain or rack path, and confirm the gate travels square. If the operator is the issue, we diagnose the motor, control board, and safety loop, not just the obvious component.
Track, Roller, and Post Alignment
Sandy soil moves. Posts that were plumb five years ago can shift enough to bind a slide gate. We reset posts in fresh concrete and adjust the track so the gate rolls without dragging.
Opener and Control Board Repairs
Older slide gate operators on Lake Placid and Lorida properties often use legacy control boards. We repair and replace boards on systems originally installed a decade or more ago. If the board can be swapped, we say so. If the whole operator is obsolete, we’ll tell you that honestly.
Wrought Iron Gate Repair in Lake Placid
Wrought Iron Gate Repair in Lake Placid typically runs $185 – $420 for hinge rebuilding, sag correction, and weld repairs on driveway and garden gates. Humid summers and heavy rain corrode iron hinges and latches, and gates seize while owners are away. When a gate sits unused from spring to fall, rust builds in the hinge barrels and the gate won’t swing when you return.
We repair iron gates the same way we’d want our own fixed. Hinge replacement, post resetting, weld repair on cracked pickets or frame joints, and rust treatment before repainting. Our goal is a gate that swings freely and stays square through another wet Highlands County summer.
Hinge Rebuilding and Sag Correction
A heavy iron gate pulls on its hinges every day. Over years, hinge pins wear and barrels elongate. The gate drops. We rebuild hinges rather than just tightening bolts, because Lake Placid’s humidity makes the underlying corrosion worse than it looks.
Weld and Rust Repair
We cut out rusted sections, weld in new steel, and treat the affected areas before finishing. For gates near Lake Placid’s lakes and irrigation, rust travels fast. The repair needs to be structural, not cosmetic.
Trusted Brands We Service in Lake Placid
We work on LiftMaster, FAAC, BFT, and Mighty Mule systems specifically, including legacy models that other companies won’t touch. For Lake Placid customers, we carry common replacement boards, photocells, receiver boards, and hinge hardware on our trucks, so we can often repair in one trip instead of ordering parts and coming back. Rural properties out toward Lorida don’t need a repair that takes two weeks because a part had to be shipped. If we know your system is a common brand, we come prepared.
Older Gate Repair specialists are hard to find. We’re not a multi-trade shop where gate work is a side service. Every part we stock, every diagnostic tool we carry, and every training hour our techs log is focused on gates.
Common Gate Repair Problems We See in Lake Placid Homes
- Corroded hinges and latches from humid summers. Gates seize while owners are away up north, and the problem is only discovered at the start of snowbird season when the gate won’t swing open.
- Sandy soil shifting gate posts. Swing gates sag and slide gates bind as posts lean over time. We reset the post and correct the gate geometry.
- Obsolete control boards failing after storms or power surges. Legacy FAAC and BFT boards die without warning, leaving a gate stuck open or closed. We repair or replace the board without pushing a full operator swap unless it’s genuinely necessary.
- Seasonal battery and opener failures. Gates that sit unused for months drain batteries and develop contact corrosion. Fall repair calls around Lake Placid and Lorida often come down to a dead battery or a corroded terminal block that would never fail in year-round use.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Lake Placid, FL
Here’s what Lake Placid homeowners can expect, based on the work we typically see across 33852 and 33862:
- Hinge and latch repair: $185 – $320
- Post reset and sag correction: $280 – $450
- Control board replacement: $240 – $480 depending on brand and availability
- Weld and rust repair: $220 – $420 depending on the extent of corrosion
- Photocell or safety sensor replacement: $150 – $280
These are honest ranges for the Lake Placid market, not national averages. What moves the number is how long the gate has been neglected, how far the post has shifted, and whether the operator board is available or obsolete. We quote the full price before any work starts. No surprises on the invoice. Call (866) 976-0095 for a free estimate.
We Also Serve Cities Near Lake Placid
Our team handles gate repair throughout Highlands County and the surrounding area. In addition to Gate Repair in Lake Placid, we regularly take calls from Sebring, Avon Park, Zolfo Springs, and Frostproof. If your gate is failing anywhere in that area, give us a call and we’ll confirm coverage and schedule a visit.
Serving Lake Placid, FL — Our Local Coverage Area
We’re based in the Lake Placid area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Lake Placid
Yes. We repair and retrofit older gates in Lake Placid all the time, and we can bring them into compliance with current UL 325 safety standards by adding photocells, safety edges, and proper entrapment protection without replacing the entire gate. We recently serviced a swing gate on a ranch property off CR 621 in Lake Placid where the homeowner returned for the season to find the LiftMaster operator dead and the hinge post leaning. Our tech replaced the control board, performed sag correction by resetting the hinge post in fresh concrete, and added a safety photocell to meet UL 325. The gate now runs smoothly for their seasonal stays. Call (866) 976-0095 to ask about your specific gate.
If the operator is a common brand like LiftMaster, FAAC, BFT, or Mighty Mule and the board or battery is still available, repair is usually the cheaper answer, often $240 – $480 for a board replacement versus $1,200+ for a new operator and install. We repair first as a matter of principle. Replacement is only our recommendation when parts are genuinely obsolete or the motor itself has failed. We’ll show you the numbers either way and let you decide. Call (866) 976-0095 and we’ll tell you honestly which path makes sense for your Lake Placid gate.
Sagging is almost always a hinge or post problem, and it can usually be fixed without replacing the gate. Lake Placid’s sandy soil allows posts to shift over time, and heavy gates gradually wear hinge barrels. We reset posts in fresh concrete, rebuild or replace hinges, and correct the gate geometry so it swings freely and latches properly. Typical cost: $280 – $450 depending on how far the post has moved.
Yes. We service rural and agricultural properties throughout 33852 and the 33862 Lorida corridor, including long-run driveway gates and pasture gates on ranch parcels. These jobs often require travel, older custom-installed hardware, and gates that have sat unused for months. We plan our schedule around those conditions, not against them. Call (866) 976-0095 with your location and we’ll confirm a visit.
For Lake Placid’s humid summers and periodic hurricane-season winds, the most effective maintenance is annual hinge lubrication, checking posts for lean, verifying the safety sensors still align, and treating rust before it spreads. When a gate sits unused for months while you’re up north, the corrosion accelerates silently. A quick fall check before your stay beats a breakdown at arrival. We can do that check as part of any repair visit.
Contact Us for Gate Repair in Lake Placid, FL
If your gate is sagging, seized, or the opener won’t respond, don’t wait until it fails entirely. Call Tampa Gate Company at (866) 976-0095 for a free estimate. We quote the price before any work starts, we repair before we recommend replacement, and we know Lake Placid’s specific gate problems better than anyone who has to drive an hour to get here. One call to a specialist.
Written by Noel Carver, Owner at Tampa Gate Company, serving Lake Placid and Highlands County with honest, repair-first gate service.